- Marvel Series 8 Mark Iii
- Marvel Series 8 Mark 1 Manual Transmission
- Marvel Series 8 Mark 1 Manual Download
- Luke 1
- Marvel Series 8 Mark Ii
- Marvel Series 8 Mark 1 Manual Pdf
Marvel Series 8 Mark 1 Bandsaw. Stock Number: BA010 Manufacturer: Marvel Serial: 821824-W Age: Model: SERIES 8 MARK 1 Condition: Good Overview: Machine has been cleaned, tested, & Painted. Please note that the machine may be seen under power in our warehouse. Machine is out of government service. Marvel Series 8 Mark I Manual Marvel Series 8 Mark I Manual Chapter 1: Marvel Series 8 Mark I Manual case 580 super e operator manual, corporate governance board practices incentives and governing risks oecd publishing, 2010 mercedes benz slk350 service repair manual software, global forum on transparency and exchange of.
At Amada Marvel we are committed to providing industry leading customer service. To contact our service team please call 800-472-9464 or fill out a service request form below.
Our technical service and customer service team will work with you to find solutions
We will keep your AMADA MARVEL and SPARTAN band saws and ironworkers operating at peak performance.
Marvel Series 8 Mark Iii
Our in house service technicians have the knowledge and expertise to help troubleshoot any problems you may experience, and can provide the information you need on service parts, maintenance procedures and a wide variety of related topics. When you schedule a service call one of our factory trained technicians will be sent either from the factory in Oshkosh, Wisconsin or from one of our regional technical support centers located around the U.S.
We provide genuine AMADA MARVEL factory repair parts.
Our large inventory ensures that we will have the parts you need, when you need them.
Information on repair parts is readily available 24/7 through our Amada Marvel genuine repair parts website, www.marvelbandsawparts.com. Whether you are looking for parts for a relatively new model or a vintage Amada Marvel, you can easily find it with this easy to use site. The site contains exploded view drawings for dozens of models with pricing and availability for all parts in stock.
Our experienced, knowledgeable service team members are committed to your satisfaction.
Fill out the form below and we will assist you.
Vertical Tilt-Frame Band Saws
- All-Mechanical Design
- Cast Iron Construction
- Metal Cutting
- Large Adaptable Work Table
Related products
18' x 22'
18' x 12.75'
50-450 fpm infinitely variable speed drive system.
Allows blade speed to be adjusted from operator's control station.
0 - 140 lbs. infinitely variable direct reading scale balance beam.
Work area 24.25' x 33'; table height 34.5'; four machined T-slots accept .625' (15.5 mm) T-Bolts.
Column and blade tilt up to 45° right and left of vertical; work always stationary. Built in protractor.
Maximum opening 18'. Jaws can be shifted to either right or left side of blade. Jaws are 6' high, 12' wide.
Adjustable stops can be pre-set to stop advance and return of blade and to stop motor at any location within the 18' travel of the blade.
Built in with Flood system, available with added optional drop lubrication system. Controlled by on-off selector switch at operator's station. Tank capacity 21 gallons.
Washes chips from hard-to-get-at places reducing clean-up time.
Together with blade wipers and flood coolant keep blade teeth free of chips.
Marvel Series 8 Mark 1 Manual Transmission
Guides are stationary and can be rotated to present new guiding surface to the blade. Upper and lower guides have preloaded carbide-faced back-up blocks to support back edge of the blade.
14' 6' Long x 1' Wide x .035' Thick. One Welded-Edge Band Blade is furnished with each machine.
Marvel Series 8 Mark 1 Manual Download
Main; 5 H.P., 1800 RPM, totally enclosed fan cooled. Coolant Pump; 1/8 H.P. enclosed motor-built-in integrally.
If ordering the 575 volt machine, it will be wired for 480 volt operation and a transformer will be provided with the machine.
A Phase-A-Matic phase converter is shipped with the machine and a 40 AMP service is required.
Column 6” longer than standard, providing increased vertical capacity to 28” at vertical position and 17” high at 45°.
10” high x 12” wide in place of standard jaws provided with machine. Do not permit miter cutting.
In place of standard jaws provided with machine. One Front Jaw and one Rear Jaw, both mitered 45°, 10” high x 12” wide.
Modification of standard column to add 3° forward approach angle, for increased efficiency in cutting of structural materials. Note: Changes horizontal capacity to 17”.
Modification of standard High Column to add 3° forward approach angle. Note: Changes horizontal capacity to 16.75”.
120 – 1080 fpm (36 – 329 m/min); main motor changed to 10 H.P., totally enclosed, fan cooled. Only available in 460-3-60 volt machine order.
Drop Lubrication System. (Requires compressed air connection 60-120psi) SUPPLEMENTARY EQUIPMENT UPON REQUEST.
Luke 1
5’0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, two stands, one end stop, and mounting bracket.
5’ 0” LONG, five ball bearing rollers, 2.5” diameter, spaced on 12” centers, one stand, attached to the first section dead roller.
First Section Dead Roller Conveyor Free Standing
5’ 0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, two stands, and one end stop.
5’ 0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, with one stand.
Marvel Series 8 Mark Ii
First Section Dead Roller Conveyor with Manual Length Gauge
10’ 0” LONG, ten ball bearing rollers, 2.5” diameter, spaced on 12” centers, includes Dead Stop, Tilting Type Gauge; manually operated.
Marvel Series 8 Mark 1 Manual Pdf
5’ 0” LONG, five ball bearing rollers, 2.5” diameter, spaced on 12” centers. Equipped with gauge rail and measuring tape extensions.